Bumper défectueux

Tout ce qui concerne le support des flippers électroniques avec écran numérique ou alphanumérique
Répondre
Laurent Caudrelier
Messages : 17
Enregistré le : mar. janv. 10, 2023 7:17 am

Bumper défectueux

Message par Laurent Caudrelier »

Bonjour

J'aimerai remplacer mes 3 bumpers sur mon flipper zaccaria locomotion 81 car il ne fonctionnent plus correctement seulement 2 sur 3.Suis-je obligé de rester dans la marque zaccaria ou une autre marque peu convenir ?En attaché la photo d'un des bumper.
Merci pour vos conseils
Vous n’avez pas les permissions nécessaires pour voir les fichiers joints à ce message.
Avatar du membre
Wanted
Messages : 5679
Enregistré le : dim. déc. 10, 2017 7:58 pm
Localisation : Etalle en province de Luxembourg

Re: Bumper défectueux

Message par Wanted »

Je crains que tu ne doives y rester.

Il existe cependant certaines compatibilités pièce par pièce.

Voici ce qui vient de chez Zaccaria pinball. Google est ton ami si tu ne comprends pas tout

Pop Bumpers

- Yokes (the fibre/metal bridge piece between the plunger and the rod and ring assembly):
Use Pinball Resource part numbers GTB-A2662+ and GTB-A12149. These are "Gottlieb" parts, but the same part from any Bally, Williams or Gottlieb supply should work. The original Williams ones are flat, and often the metal part breaks. The Gottlieb design is braced along one edge and is much stronger. I'm pretty sure Clay shows this somewhere on http://www.marvin3m.com/fix.htm if you want to see the details. It's probably in at least one of the Williams repair guides.
- Body and Cap:
I can't prove it right now, but these look exactly like Gottlieb EM parts. The artwork, of course, is different, but it looks like you could substitute Gottlieb parts if you had to here.
- Skirt:
Standard part, any Williams, Bally or Gottlieb should work. The originals don't have a "nub" on them, many replacements do. Depending on the orientation of the pop bumper, you may be able to leave the nub, or you might have to sand it off.
- Rod and Ring Assembly:
Standard part. Any Williams, Bally, or Gottlieb part should fit here. The plastic ones (Stern, Data East) will not work.
- Bracket:
I don't have any Gottlieb pop bumper parts to compare these to. The Bally or Williams bracket can be made to work, but neither is actually a drop in replacement. The problem is in the mounting holes for the screws where the bracket attaches to the playfield. The two on the sides line up ok, but the one on the rear (middle) does not line up. It looks like the Williams bracket has a little bit more metal, and is probably the better one to get if you have to do this. There should be room to drill a new mounting hole in the tab of the bracket to make this fit.
- Plunger:
Use the Williams plunger. It's black, instead of chromed, but is otherwise identical.
- Return Spring:
Use the Williams spring. It's identical.
Laurent Caudrelier
Messages : 17
Enregistré le : mar. janv. 10, 2023 7:17 am

Re: Bumper défectueux

Message par Laurent Caudrelier »

Je pense qu'au niveau mécanique je devrais m'en sortir , mais est-ce que je sais trouver une bobine équivalente dans une autre marque ?
Avatar du membre
Wanted
Messages : 5679
Enregistré le : dim. déc. 10, 2017 7:58 pm
Localisation : Etalle en province de Luxembourg

Re: Bumper défectueux

Message par Wanted »

Laurent Caudrelier
Messages : 17
Enregistré le : mar. janv. 10, 2023 7:17 am

Re: Bumper défectueux

Message par Laurent Caudrelier »

Merci
Je pense que cela va m'aider énormément.

Belle soirée
Répondre